ASG 29 S
Our ASG 29 S is a modern hig performance glider with very good versatile flying qualities. The computed airfoil of thickness 11-9% is perfectly suited for this use and allows a wide speed range. Circling with the ASG 29 S in a weak thermal lift is easy, and due to its low drag and excellent conversion between altitude and speed it is perfectly suitable for aerobatics and high speed flight.
Flaps and ailerons are hinged at the lower side, hence touching down at the slope is comfortable thanks to the crow configuration of the flaps. With a mass of only 14.5 kg the ASG is very light, and fitted with a CEFLIX 500 EDF it is able to self-launch on a grassy runway.
Because of the thin airfoil the wing is built in an all carbon hard shell technique, and the square wing
joiner of dimensions 18x40 mm is made of carbon, too. The stability of the wing is very high and well
suited for velocities above 300 km/h even at demanding conditions.
price: on request
All photos of the ASG 29
S...
For price inquiries and offers please
contact us by MAIL.
Technical details
| wing span | 6000 mm |
| fuselage length | 2190 mm |
| takeoff weight glider without landing gear | from 11 kg |
| takeoff weight complete with drive Jetec E90 (12S 5000mA) excellent for grass slopes! | 14,5 kg |
| area | 116 qdm |
| airfoil thickness | 11 % - 9 % |
| scale | 1:3 |
| center of gravity | 65 mm without wing (with CPR) |
Flap settings
| Aileron |
| Included flap (2 flaps) In normal flight switch off the flap. ↑ 10 mm↓ 3 mm Inner side measurement ↑ 8 mm↓ 3 mm Aileron measured outside |
| Thermal and speed aerobatic |
| Thermal ↓ 7 mm Flap Inner side measurement ↓ 1 mm Aileron measured outside Speed Aerobatic ↑ 5 mm Flap Inner side measurement ↑ 1 mm Aileron measured outside |
| Landing (Butterfly) |
|
↓ max Flap Inner side measurement Please check that the servo has the
mechanical end and the mylar tape is inside. ↑ 3 mm Aileron measured outside ↓ 3 mm Elevator mix measured inside |
| Elevator |
| ↑ 10 mm↓ 10 mm measured outside |
| Rudder |
| 40 mmmax. |
| All dimensions in millimeters (mm). |
The specified values result in very agile flight behavior. Individual deviations are possible. RAL tone 9003 2K (white). Attention, please clean the paint only with polish (no acetone or spirit) !!! Inner wing packing dimension 2850 mm.
Servos with power
| Description | Actuating Power | Application |
|---|---|---|
| KST X10 10mm | 2x Aileron, 1x Brake | |
| Servo KST A15 1810 15mm | 18 kg | 2x Flap, 1x Elevator, 1x Rudder, 1x Tow release |
| Hitec HS-7954 | 1x Gear |
Kit Standard
- full carbon wing with 2 flaps
- wing prepared for crossover servo linkage
- 18 x 40 mm carbon wing joiner
- fuselage reinforcements with additional glas fibres in the cockpit area and UD-carbon in the tail boom
- canopy mechanics with gas spring + pilot seat + cockpit side covers included
- wing lock system with M6 screw installed
- wing length without winglet 2850 mm
- wings and elevator assembled
- compound paint with high UV resistance
- fuselage seam line painted over
Optionally available against surcharge:
- canopy installation
- gear installation
- scale cockpit with instruments, harness, stick, and all levers